RCU Forums
0 2022/06/12 05:44:29
0 2022/06/12 05:43:25
Rebuilt nose
Rebuilt nose
0 2022/06/12 05:42:42
White elephant
White elephant
0 2022/06/12 05:25:54
0 2022/06/12 05:24:04
White elephant
White elephant
0 2022/06/12 05:23:09
White elephant
White elephant
0 2022/06/12 05:21:21
All tanks and wood for support are about 210 gr.
All tanks and wood for support are about 210 gr.
0 2020/04/09 01:43:16
The air tanks aregment. Each one is secured with valcro and wooden bracket. Note one of the smaller tanks has a removable bracket. The big tank is almost in center to give space for one of the hot air vents.
The air tanks aregment. Each one is secured with valcro and wooden bracket. Note one of the smaller tanks has a removable bracket. The big tank is almost in center to give space for one of the hot air vents.
0 2020/04/09 01:39:53
0 2020/04/09 01:39:23
Each tank is secured with but not only valcro strips.
Each tank is secured with but not only valcro strips.
0 2020/04/09 01:38:04
0 2020/04/09 00:46:55
Final tesolt.
Final tesolt.
0 2020/04/01 01:26:14
0 2020/04/01 01:25:33
The vent port location was done in that place in the upper fuselage as the hot air tends to climb up and with the forward movment of the plane it tends to move back.
The vent port location was done in that place in the upper fuselage as the hot air tends to climb up and with the forward movment of the plane it tends to move back.
0 2020/04/01 01:22:36
The tail pipe is about 30 mm out of the fuselage. This will not generate too much heat to harm the skin. The kit comes with two thin metal plates to be added in this location. I didn't used them because they are not part of the full scale plane and the area can handle the temp.
The tail pipe is about 30 mm out of the fuselage. This will not generate too much heat to harm the skin. The kit comes with two thin metal plates to be added in this location. I didn't used them because they are not part of the full scale plane and the area can handle the temp.
0 2020/03/31 12:55:51
Double tail pipe. This is why it can't be moved rearward too much. Note the 3 air tanks. The right one must be removed if the tail pipe has to go out.
Double tail pipe. This is why it can't be moved rearward too much. Note the 3 air tanks. The right one must be removed if the tail pipe has to go out.
0 2020/03/31 12:39:01
Almost there...
Almost there...
0 2020/03/31 12:37:34
The starter is looking forward through the inlet duct just to be engaged...
The starter is looking forward through the inlet duct just to be engaged...
0 2020/03/31 12:36:02
Engine bay final mesurments. The engine rails had to be shaped to acomodate the engine. The fuel vent lines waiting to be instald.
Engine bay final mesurments. The engine rails had to be shaped to acomodate the engine. The fuel vent lines waiting to be instald.
0 2020/03/31 12:32:34
0 2020/03/31 04:47:27
0 2020/03/31 04:46:35
0 2020/03/31 04:43:25
The initial location of one of the antennas-white plastic tube and the wire I used to check the hole done in the fuselage for getting the antenna out.
The initial location of one of the antennas-white plastic tube and the wire I used to check the hole done in the fuselage for getting the antenna out.
0 2020/03/31 04:35:39
Second receiver antenna was directed outside of the fuselage and got a hand made aero-shaped antenna made from epoxy resin.
Second receiver antenna was directed outside of the fuselage and got a hand made aero-shaped antenna made from epoxy resin.
0 2020/03/31 04:32:13
Second receiver antenna was directed outside of the fuselage and got a hand made aero-shaped antenna made from epoxy resin.
Second receiver antenna was directed outside of the fuselage and got a hand made aero-shaped antenna made from epoxy resin.
0 2020/03/31 04:28:37
One of the receivers antennas is facing up through the cockpit floor.
One of the receivers antennas is facing up through the cockpit floor.
0 2020/03/31 04:21:20
This is the horizontal tray for both fuel manual valve, turbine connector and ECU. It was later replaced with non carbon material.
This is the horizontal tray for both fuel manual valve, turbine connector and ECU. It was later replaced with non carbon material.
0 2020/03/31 04:04:31
Small plywood block inserted between the "L" metal hinges to prevent them from falling.
Small plywood block inserted between the "L" metal hinges to prevent them from falling.
0 2020/03/30 13:20:32
0 2020/03/30 13:20:14
Note the angle of canopies opening.
Note the angle of canopies opening.
0 2020/03/30 13:19:24
0 2020/03/30 13:09:51
Marking the rear fin parts location.
Marking the rear fin parts location.
0 2020/03/30 12:58:58
Rear lower fin assembly with the reinforcement pins. Not mandatory but better.
Rear lower fin assembly with the reinforcement pins. Not mandatory but better.
0 2020/03/30 12:57:25
Size dose mstters!
Size dose mstters!
0 2020/03/30 12:56:16
Home made 4th wheel. Later painted in white.
Home made 4th wheel. Later painted in white.
0 2020/03/30 12:55:25
I just sleep better knowing they are like this 😄
I just sleep better knowing they are like this 😄
0 2020/03/30 11:46:36
Second version made from 3 mm playwood psinted white. I still want to add batteries volt meters. I aldi decided to skip the well proven powerbox digiswitch and used the HD Smartfly switch to go together with the excellent Smartfly eq 10.
Second version made from 3 mm playwood psinted white. I still want to add batteries volt meters. I aldi decided to skip the well proven powerbox digiswitch and used the HD Smartfly switch to go together with the excellent Smartfly eq 10.
0 2020/03/30 11:34:57
First version. Cool but I was bothered from radio interferance. Note that the horizontal surface goes further and uses as the tray/bracket for the turbine ECU.
First version. Cool but I was bothered from radio interferance. Note that the horizontal surface goes further and uses as the tray/bracket for the turbine ECU.
0 2020/03/30 11:31:35
Both trays completed.
Both trays completed.
0 2020/03/30 11:11:24
Advertising | Cookie Policy | Privacy Statement | Terms of Service | Manage Preferences Your Privacy Choices
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.